Self-Leveling Epoxy

Perdüre SLE & SLE-T

Perdüre SLE (self leveling epoxy) & SLE-T (self leveling epoxy trowell grade ) consists of 100% solids epoxy and selectively graded aggregates to produce a seamless flooring solution ideally suited for industrial flooring applications. It is designed to restore and replace eroded or spalled concrete floors. When sealed, Perdüre SLE & SLE produce a dense, skid inhibiting surface that eliminates dirt and chemical penetration. The chemical resistance and overall performance of Perdüre SLE & SLE-T can be increased by using different epoxy and polyurethane top coats.

Since no two floors are the same, Perdüre SLE & SLE-T systems are modified to handle various degrees to chemical, impact and thermal shock resistance. It is applied in thickness ranging from one-sixteenth inch to one-fourth inch. Perdüre SLE & SLE-T is applied as a three-component system of 100% solids epoxy primer, 100% solids epoxy body coat that is blended with self-leveling filler and a polyurethane or polyaspartic topcoat.

Note: The thickness of Perdüre SL_e and Perdüre SL_e(t) system is modified by changing the number of coats of self-leveling filler and Perdüre E10 or by changing the size and/or quantity of the filler in Perdüre E10. Please confer with Düraamen technical representative to arrive at specifications for your project.

Perdüre E02

Perdüre E02 is a 100% solids, moisture tolerant epoxy primer for concrete and masonry surfaces. It combines the properties of water insensitivity with good wetting properties. It provides excellent filling and sealing properties needed under high performance epoxy floor coatings on concrete. The moisture tolerance of perdüre E02 allows it to be applied to damp concrete after surface preparation. This includes bonding “old to old” or “new to old” concrete.

advantages

• Low modulus – stress relieving
• Fast cure formulation available for priming under coatings
• Moisture insensitive cure
• Conforms to ASTM C-881 requirements
• Low viscosity-good wetting properties

TECHNICAL DATA			CURE/DRY TIME
Viscosity @ 75°F	400 – 450cps		Pot Life	30-40 minutes @ 75°F
Mixing Ratio	2 parts A to 1 parts B by volume		Dry to Touch	6–8 hours @ 75°F
Solids Content	100% Solids by volume		Re-Coat (regular cure)	10–12 hours @ 75°F
Volatile Organic Content	0		Re-Coat (fast cure)	4-6 hours @ 75°F
Gloss, 60°F	Low sheen		Full cure, maximum resistance	5 days
Weight Per gallon	9.00–9.50 pounds per gallon, mixed

Perdüre E10

Perdüre E10 is a 100% solids, multipurpose epoxy binder for Düraamen self leveling mortar and quartz systems. This all purpose epoxy resin is characterized as an excellent general purpose material with good clarity and color retention. It is essentially odorless and therefore can be applied in occupied areas.

ADVANTAGES

• Good troweling properties when used with Duraamen self –leveling epoxy mortar and quartz systems
• Excellent color retention when used as a topcoat with Düraamen flooring systems
• Good troweling properties when used in mortar systems
• Low odor for use in occupied areas
• Available in fast cure systems
• USDA approved for food handling applications

TECHNICAL DATA			CURE/DRY TIME
Viscosity @ 75°F	950cps		Pot Life	30-40 minutes
Mixing Ratio	4 parts A to 1 parts B by volume		Dry to Touch	6-8 hours @ 75°F
Solids Content	100% by volume		Re-coat (regular cure)	10-12 hours @ 75°F
Volatile Organic Content	0		Re-coat (fast cure)	4-6 hours @ 75°F
Gloss 60°F	85-100		Full cure, max. resistance	48 hours
Weight Per gallon	9.00-9.50 pounds per gallon, mixed
VOC	Zero

Performance Properties
Tensile Strength ASTM D638	8500psi
Elongation ASTMD638	5.5%
Adhesion to Metal	2500psi
Adhesion to Concrete ACI403	350psi (concrete fails)
Hardness ASTM D2240	80 (Shore D)
Service Temperature MIL D 3134F	160F (immersion) 185F (dry heat)
Abrasion resistance ASTM C501	35-40 mg loss (CS-17 wheel, 1kg load, 1000loads)
Impact Resistance, MIL D3134F	Withstands 16ft/lb – no cracking, delamination or chipping
Indentation MILD-3134F	Withstands 2000lb/sq.in for 30min without indentation
Water Absorption ASTM D 670 63 (24hr immersion)	0.10% maximum
Flexural Strength, ASTM D790	8000psi
Compressive Strength, ASTM D 695	11000psi

Perdüre E20

Perdüre E20 is a 100% solids, pigmented epoxy floor coating designed to provide high gloss, chemical resistant protection. Perdüre E20 should be used wherever a high build, corrosive resistant, protective floor coating is required. It is essentially odorless and can, therefore, be used in occupied areas. Perdüre E20 provides a smooth, high gloss finish or, in a heavy body form, an orange peel, texture finish.

ADVANTAGES

• Low odor during application and cure
• Zero VOC
• Easy application and clean-up

TECHNICAL DATA			CURE/DRY TIME
Viscosity @ 75°F	950cps		Pot Life	30-35 minutes
Mixing Ratio	2 parts A to 1 parts B by volume		Dry to Touch	10–12 hours @ 75°F
Solids Content	100% by volume		Re-coat	12–16 hours @ 75°F
Volatile Organic Content	0		Light Traffic	24 hours @ 75°F
Weight Per gallon	11.5 pounds per gallon, mixed		Full cure, max. resistance	5 days

Perdüre NE25

Perdüre NE25 is a 100% solids epoxy modified with Novolac epoxy floor coating designed to provide high chemical resistant protection. Perdüre NE25 should be used whenever a high build, acid and alkali resistant, protective floor coating is required. It is essentially odorless and therefore, can be used in occupied areas. Perdüre NE25 provides a smooth, high gloss finish or, in a heavy body form, an orange peel, textured finish. It is used as a finish coating for High Performance Industrial Floor Systems.

ADVANTAGES

• Superior chemical and stain resistance
• Easy of application
• Bonds very well to cool and damp substrates
• Low odor for use in occupied areas (zero-VOC)
• Suitable for immersion and wet process flooring applications

TECHNICAL DATA			CURE/DRY TIME
Viscosity @ 75°F	1000cps		Pot Life	20-25 minutes
Mixing Ratio	2 parts A to 1 parts B by volume		Dry to Touch	6-8 hours @ 75°F
Solids Content	100% by volume		Re-coat	12–16 hours @ 75°F
Volatile Organic Content	0		Light Traffic	24 hours @ 75°F
Weight Per gallon	11.5 pounds per gallon, mixed

Perdüre NE30

Perdüre NE30 is a 100% solids epoxy novolac coating ideal for severe chemical and solvent resistant applications. Low viscosity make Perdüre NE30 ideal use as a binder in trowelled mortar and slurry systems where resistance to 98% sulphuric acid or other strong caustics is needed. Perdüre NE30 is excellent for secondary containment, solvent storage, pump pads, trenches and other high exposure areas.

ADVANTAGES

• Low viscosity ideal for trowelled mortar and slurry applications
• Exhibits excellent resistance to strong acids, alkalis and most industrial chemicals and solvents
• 100% Solids – low odor during application and curing

TECHNICAL DATA			CURE/DRY TIME
Viscosity @ 75°F	1000–1500cps		Pot Life	20–25 minutes @ 75°F
Mixing Ratio	2 parts A to 1 parts B by volume		Dry to Touch	6–7 hours @ 75°F
Solids Content	100% by volume		Re-coat	8–12 hours @ 75°F
Volatile Organic Content	0		Light Traffic	24 hours @ 75°F
Weight Per gallon	11.00–11.50 pounds per gallon, mixed		Full cure, max. resistance	5 days

Perdüre U50

Perdüre U50 is a two-component, chemical resistant, polyurethane coating.
Click here to go to the Perdüre U50 page